[Full Version] Download Free Cisco 300-370 Exam Questions And Answers From Lead2pass (31-40)

admin   December 1, 2016   Comments Off on [Full Version] Download Free Cisco 300-370 Exam Questions And Answers From Lead2pass (31-40)

2016 December Cisco Official New Released 300-370 Dumps in Lead2pass.com!

100% Free Download! 100% Pass Guaranteed!

Lead2pass 300-370 braindumps including the exam questions and the answer, completed by our senior IT lecturers and the Cisco product experts, include the current newest 300-370 exam questions.

Following questions and answers are all new published by Cisco Official Exam Center: http://www.lead2pass.com/300-370.html

QUESTION 31
An engineer is troubleshooting AP join issues on a wireless infrastructure. While gathering debugs, the engineer notices that one of the commands may generate an excessive an excessive amount of data on the console. Which command causes this to occur?

A.    debug capwap detail enable
B.    debug capwap errors enable
C.    debug capwap info enable
D.    debug capwap events enable
E.    debug capwap packet enable
F.    debug capwap payload enable

Answer: B

QUESTION 32
Drag and Drop Question
Drag and drop the Layer 3 WLAN controller mutual authentication join process events on the left into the order in which they occur on the right Not all options are used.

Answer:

QUESTION 33
A WLAN was installed at a high AP density. DTPC is lowering the transmit power of many APs too low. Which change m the DTPC transmit power threshold must be made to allow APs to globally increase AP transmit power by 3dBm?

A.    from 70 dBm to 73 dBm
B.    from -70 dBm to -73 dBm
C.    from 70 dBm to 67 dBm
D.    from -70 dBm to -67 dBm

Answer: D

QUESTION 34
A user reports being unable to connect to a server with a certain program while connected to wireless. Wh.ch troubleshooting methodology can be used to begin the troubleshooting process?

A.    top-down
B.    shoot from the hip
C.    follow the path
D.    bottom-up
E.    divide and conquer

Answer: A

QUESTION 35
A client is failing EAP authentication and a debug shows that the server is sending an Access-Reject message. Which action must you take to resolve authentication?

A.    Verify that the Validate server certificate on the client is disabled.
B.    Verify that the client certificates are from the proper CA and server certificate.
C.    Verify that the client server certificate has the proper Windows OlDs.
D.    Verify that the user account is the same in the client certificate.
E.    Verify that the user is using the same password that is on the server

Answer: B

QUESTION 36
When implementing interface groups, how are the IP addresses sourced via DHCP for wireless clients?

A.    through the primary interface of the group
B.    through round robin between interfaces
C.    through interface group definition
D.    through the interface receiving the first response

Answer: B

QUESTION 37
Which three steps would a network engineer use to troubleshoot an AP join problem? (Choose three.)

A.    Validate the STP configuration.
B.    Verify the ping AP from the controller.
C.    Verify the ping AP from the client.
D.    Verify that the AP is getting an address from the DHCP server.
E.    I Validate the SNMP configuration.
F.    Verify the authentication configuration parameters.

Answer: ABF

QUESTION 38
An engineer has run the debug dhcp packet enable command on the wireless LAN controller CLI. Which field contacts the IP address offered to the client?

A.    siaddr
B.    ciaddr
C.    chaddr
D.    yiaddr
E.    giaddr

Answer: C

QUESTION 39
Refer to the exhibit. Access points ate deployed in an office building and users report that the real-time communications quality of experience is poor when users walk between the elevators The elevators are a heavy metallic obstacle, and AP 3 was installed to cover the elevator area, which AP t and AP 2 signal does not reach Communications are captured for a user walking from point A to point C. and it is observed that the user iPhone device suddenly scans all bands and then roams from AP I to AP 3 somewhere between points B and C WLAN is set to 5 GHz only. Open, default rate configuration.
Which action improves the real-time application quality of experience in this area?

 

A.    Enable 802 11v on the WLAN
B.    Enable 802 11r on the WLAN
C.    Enable 802 11k on the WLAN
D.    Move AP 2 to point B

Answer: B

QUESTION 40
A mobile workstation in a factory contains an AP that is configured as a workgroup bridge.
When the workstation moves, it loses connectivity and disrupts operation.
What can the engineer implement to minimize roaming problems?

A.    Use 802.1X authentication.
B.    Use Cisco Centralized Key Management for fast roaming.
C.    Use AES for encryption.
D.    Use the mobile station command.

Answer: D

If you use Lead2pass braindump as your 300-370 exam prepare material, we guarantee your success in the first attempt. Lead2pass 300-370 dump provides you everything you will need to take your 300-370 Exam.

300-370 new questions on Google Drive: https://drive.google.com/open?id=0B3Syig5i8gpDeXZTcXZnWk5naVU

2016 Cisco 300-370 exam dumps (All 70 Q&As) from Lead2pass:

http://www.lead2pass.com/300-370.html [100% Exam Pass Guaranteed]

Lead2pass Testking Pass4sure Actualtests Others
$99.99 $124.99 $125.99 $189 $29.99-$49.99
Up-to-Dated
Real Questions
Error Correction
Printable PDF
Premium VCE
VCE Simulator
One Time Purchase
Instant Download
Unlimited Install
100% Pass Guarantee
100% Money Back